</a>led" title="led">led" title="led">led design flexibility and seamless integration to today’s demanding connectivity solutions.
LPC11U24 主要特性和優勢:
ARM Cortex-M0 processor, running at frequencies of up to 50 MHz
ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC)
Non-Maskable Interrupt (NMI) input selectable from several input sources
System tick timer
Up to 32 kB on-chip flash program memory
Up to 4 kB on-chip EEPROM data memory
Up to 10 kB SRAM data memory
16 kB boot ROM
In-System Programming (ISP) and In-Application Programming (IAP)
ROM-based USB drivers. Flash updates via USB supported
ROM-based 32-bit integer division routines
Standard JTAG (Joint Test Action Group) test interface
Serial Wire Debug
Up to 54 General-Purpose I/O (GPIO) pins
Up to 8 GPIO pins can be selected as edge and level sensitive interrupt sources
Two GPIO grouped interrupt modules
High-current source output driver (20 mA) on one pin
High-current sink driver (20 mA) on true open-drain pins
Four general-purpose counter/timers
Programmable Windowed WatchDog Timer (WWDT)
10-bit ADC with input multiplexing among eight pins
USB 2.0 full-speed device controller
USART (Universal Synchronous Asynchronous Receiver/Transmitter)
Two SSP (Synchronous Serial Port) controllers
I2C-bus interface supporting the full I2C-bus specification and Fast-mode Plus
Crystal Oscillator with an operating range of 1 MHz to 25 MHz
12 MHz high-frequency Internal RC oscillator (IRC)
Internal low-power, low-frequency WatchDog Oscillator (WDO)
PLL allows CPU operation up to the maximum CPU rate
A second, dedicated PLL is provided for USB
Clock output function with divider
Integrated PMU (Power Management Unit)
Power profiles residing in boot ROM
Four reduced power modes
Processor wake-up
Power-On Reset (POR)
Brownout detect with four separate thresholds for interrupt and forced reset
Unique device serial number for identification
Single 3.3 V power supply (1.8 V to 3.6 V)
Temperature range -40 ℃ to +85 ℃
LPC11U24 應用:
Consumer peripherals
Medical
Industrial control
Industrial control
USB audio devices
圖1.LPC11U24 框圖
圖2.自供電設備的USB接口連接圖
Rapid Prototyping for USB devices, battery applications and low-cost 32-bit ARM® Cortex™-M0 based designs
圖3.mbed NXP LPC11U24 MCU模塊外形圖
The mbed NXP LPC11U24 Microcontroller in particular is designed for prototyping low cost USB devices, battery powered applications and 32-bit ARM® Cortex™-M0 based designs. It is packaged as a small DIP form-factor for prototyping with through-hole PCBs, stripboard and breadboard, and includes a built-in USB FLASH programmer.
圖4.mbed NXP LPC11U24 MCU模塊連接圖
圖5.mbed NXP LPC11U24 MCU模塊電路圖(1)
圖6.mbed NXP LPC11U24 MCU模塊電路圖(2)
圖7.mbed NXP LPC11U24 MCU模塊電路圖(3)
圖8.mbed NXP LPC11U24 MCU模塊電路圖(4)
詳情請見:
http://www.nxp.com/documents/data_sheet/LPC11U2X.pdf
和
http://mbed.org/media/uploads/chris/mbed-010.2-schematic.pdf
以及
http://www.nxp.com/documents/user_manual/UM10462.pdf
LPC11U24 主要特性和優勢:
ARM Cortex-M0 processor, running at frequencies of up to 50 MHz
ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC)
Non-Maskable Interrupt (NMI) input selectable from several input sources
System tick timer
Up to 32 kB on-chip flash program memory
Up to 4 kB on-chip EEPROM data memory
Up to 10 kB SRAM data memory
16 kB boot ROM
In-System Programming (ISP) and In-Application Programming (IAP)
ROM-based USB drivers. Flash updates via USB supported
ROM-based 32-bit integer division routines
Standard JTAG (Joint Test Action Group) test interface
Serial Wire Debug
Up to 54 General-Purpose I/O (GPIO) pins
Up to 8 GPIO pins can be selected as edge and level sensitive interrupt sources
Two GPIO grouped interrupt modules
High-current source output driver (20 mA) on one pin
High-current sink driver (20 mA) on true open-drain pins
Four general-purpose counter/timers
Programmable Windowed WatchDog Timer (WWDT)
10-bit ADC with input multiplexing among eight pins
USB 2.0 full-speed device controller
USART (Universal Synchronous Asynchronous Receiver/Transmitter)
Two SSP (Synchronous Serial Port) controllers
I2C-bus interface supporting the full I2C-bus specification and Fast-mode Plus
Crystal Oscillator with an operating range of 1 MHz to 25 MHz
12 MHz high-frequency Internal RC oscillator (IRC)
Internal low-power, low-frequency WatchDog Oscillator (WDO)
PLL allows CPU operation up to the maximum CPU rate
A second, dedicated PLL is provided for USB
Clock output function with divider
Integrated PMU (Power Management Unit)
Power profiles residing in boot ROM
Four reduced power modes
Processor wake-up
Power-On Reset (POR)
Brownout detect with four separate thresholds for interrupt and forced reset
Unique device serial number for identification
Single 3.3 V power supply (1.8 V to 3.6 V)
Temperature range -40 ℃ to +85 ℃
LPC11U24 應用:
Consumer peripherals
Medical
Industrial control
Industrial control
USB audio devices
圖1.LPC11U24 框圖
圖2.自供電設備的USB接口連接圖
Rapid Prototyping for USB devices, battery applications and low-cost 32-bit ARM® Cortex™-M0 based designs
圖3.mbed NXP LPC11U24 MCU模塊外形圖
The mbed NXP LPC11U24 Microcontroller in particular is designed for prototyping low cost USB devices, battery powered applications and 32-bit ARM® Cortex™-M0 based designs. It is packaged as a small DIP form-factor for prototyping with through-hole PCBs, stripboard and breadboard, and includes a built-in USB FLASH programmer.
圖4.mbed NXP LPC11U24 MCU模塊連接圖
圖5.mbed NXP LPC11U24 MCU模塊電路圖(1)
圖6.mbed NXP LPC11U24 MCU模塊電路圖(2)
圖7.mbed NXP LPC11U24 MCU模塊電路圖(3)
圖8.mbed NXP LPC11U24 MCU模塊電路圖(4)
詳情請見:
http://www.nxp.com/documents/data_sheet/LPC11U2X.pdf
和
http://mbed.org/media/uploads/chris/mbed-010.2-schematic.pdf
以及
http://www.nxp.com/documents/user_manual/UM10462.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。