</a>數字電源" title="數字電源">數字電源" title="數字電源">數字電源控制器, 能數字控制三路單獨的反饋回路,專有的基于PID硬件,2極點/2零點配置,非線性控制,高達16MHz誤差模數轉換器(EADC),可配置分辨率到1mV/LSB,自動分辨率選擇,高達8x過取樣,14位有效DAC,主要用于電源和通信整流器,功率因速修正和隔離的DC/DC模塊.本文介紹了UCD3138主要特性,方框圖,以及評估板UCD3138PFCEVM-026主要特性,電路圖,材料清單和PCB元件布局圖.
The UCD3138 is a digital power supply controller from Texas Instruments offering superior levels of integration and performance in a single chip solution. The flexible nature of the UCD3138 makes it suitable for a wide variety of power conversion applications. In addition, multiple peripherals inside the device have been specifically optimized to enhance the performance of ac/dc and isolated dc/dc applications and reduce the solution component count in the IT and network infrastructure space.
The UCD3138 is a fully programmable solution offering customers complete control of their application, along with ample ability to differentiate their solution. At the same time, TI is committed to simplifying our customer’s development effort through offering best in class development tools, including application firmware, Code Composer Studio. software development environment, and TI’s Fusion Power Development GUI which enables customers to configure and monitor key system parameters.
At the core of the UCD3138 controller are the digital control loop peripherals, also known as Fusion Digital Power Peripherals (FDPP). Each FDPP implements a high speed digital control loop consisting of a dedicated Error Analog to Digital Converter (EADC), a PID based 2 pole–2 zero digital compensator and DPWM outputs with 250 ps pulse width resolution. The device also contains a 12-bit, 265ksps general purpose ADC with up to 14 channels, timers, interrupt control, JTAG debug and PMBus and UART communications ports. The device is based on a 32-bit ARM7TDMI-S RISC microcontroller that performs
real-time monitoring, configures peripherals and manages communications. The ARM microcontroller executes its program out of programmable flash memory as well as on-chip RAM and ROM.
In addition to the FDPP, specific power management peripherals have been added to enable high efficiency across the entire operating range, high integration for increased power density, reliability, and lowest overall system cost and high flexibility with support for the widest number of control schemes and topologies. Such peripherals include: light load burst mode, synchronous rectification, LLC and phase shifted full bridge mode switching, input voltage feed forward, copper trace current sense, ideal diode emulation, constant current constant power control, synchronous rectification soft on and off, peak current mode control, flux balancing, secondary side input voltage sensing, high resolution current sharing, hardware configurable soft start with pre bias, as well as several other features. Topology support has been optimized for voltage mode and peak current mode controlled phase shifted full bridge, single and dual phase PFC, bridgeless PFC, hard switched full bridge and half bridge, and LLC half bridge and full bridge.
UCD3138主要特性:
Digital Control of up to 3 Independent Feedback Loops
Dedicated PID based hardware
2-pole/2-zero configurable
Non-Linear Control
Up to 16MHz Error Analog to Digital Converter (EADC)
Configurable Resolution as Small as 1mV/LSB
Automatic Resolution Selection
Up to 8x Oversampling
Hardware Based Averaging (up to 8x)
14 bit Effective DAC
Up to 8 High Resolution Digital Pulse Width Modulated (DPWM) Outputs
250ps Pulse Width Resolution
4ns Frequency Resolution
4ns Phase Resolution
Adjustable Phase Shift Between Outputs
Adjustable Dead-band Between Pairs
Up to 2MHz Switching Frequency
Configurable PWM Edge Movement
Trailing Modulation
Leading Modulation
Dual Edge Modulation
Configurable Feedback Control
Voltage Mode
Average Current Mode
Peak Current Mode Control
Constant Current
Constant Power
Configurable Modulation Methods
Frequency Modulation
Phase Shift Modulation
Pulse Width Modulation
Fast, Automatic and Smooth Mode Switching
Frequency Modulation and PWM
Phase Shift Modulation and PWM
High Efficiency and Light Load Management
Burst Mode
Ideal Diode Emulation
Synchronous Rectifier Soft On/Off
Low IC Standby Power
Soft Start / Stop with and without Pre-bias
Fast Input Voltage Feed Forward Hardware
Primary Side Voltage Sensing
Copper Trace Current Sensing
Flux and Phase Current Balancing for Non-Peak Current
Mode Control Applications
Current Share Bus Support
Analog Average
Master/Slave
Feature Rich Fault Protection Options
7 High Speed Analog Comparators
Cycle-by-Cycle Current Limiting
Programmable Fault Counting
External Fault Inputs
4–10 Digital Comparators
Programmable blanking time
Synchronization of DPWM waveforms between multiple UCD313x devices
14 channel, 12 bit, 265 ksps General Purpose ADC with integrated
Programmable averaging filters
Dual sample and hold
Internal Temperature Sensor
Fully Programmable High-Performance 31.25MHz, 32-bit ARM7TDMI-S Processor
32 kByte (kB) Program Flash
2 kB Data Flash with ECC
4 kB Data RAM
4 kB Boot ROM Enables Firmware Boot-Load in the Field via
I2C or UART
Communication Peripherals
I2C/PMBus
2 UARTs
JTAG Debug Port
Timer capture with selectable input pins
Up to 5 Additional General Purpose Timers
Built In Watchdog: BOD and POR
64-pin QFN and 40-pin QFN packages
Operating Temperature: –40°C to 125°C
Fusion Digital Power GUI Support
UCD3138應用:
Power Supplies and Telecom Rectifiers
Power Factor Correction
Isolated dc-dc Modules
圖1.UCD3138方框圖
評估板UCD3138PFCEVM-026
This EVM is to help evaluate the UCD3138 64-pin digital control device in off-line power converter application and then to aid its design. The EVM is a standalone Power Factor Correction (PFC) preregulator of single-phase AC input. The EVM UCD3138PFCEVM-026 is used together with its control card, UCD3138CC64EVM-030, also an EVM on which is placed UCD3138RGC.
The EVM of UCD3138PFCEVM-026 together with UCD3138CC64EVM-030 can be used as they are delivered without additional work, from either hardware or firmware, to evaluate PFC. The UCD3138PFCEVM-026 together with the UCD3138CC64EVM-030 can also be re-tuned on its design parameters through the operation of GUI, called Texas Instruments Fusion Digital Power Designer, or reloaded up with custom firmware with user’s definition and development.
The EVM system is in topology of single-phase boost converter at its delivery on both hardware and firmware, but can be re-configured into two other PFC topologies: dual-phase interleaved, and bridgeless, then corresponding operation can be made by reloading with that associated firmware. All necessity of hardware and firmware for the two additional topologies are already developed and delivered with the shipment. Please contact Texas Instruments to obtain the instructions how to make re-configuration.
In the package delivered, three EVMs are included UCD3138PFCEVM-026, UCD3138CC64EVM-030, and USB-TO-GPIO. In the same package, also included is a hard copy of Evaluation Module Electrical Safety Guideline.
This user’s guide provides basic evaluation instruction from a viewpoint of system operation in standalone PFC in its boost configuration.
UCD3138PFCEVM-026 together with UCD3138CC64EVM-030 is an EVM of PFC pre-regulator with digital control using UCD3138 device in boost converter topology and in the application of single-phase AC input.
UCD3138 device is located on the board of UCD3138CC64EVM-030. UCD3138CC64EVM-030 is a daughter card and serves all PFC required control functions with preloaded single-phase boost PFC firmware. UCD3138PFCEVM-026 accepts universal AC line input from 90 VAC to 264 VAC, and outputs nominal 390 VDC with full load output power 360 W, or full output current 0.92 A.
圖2.評估板UCD3138PFCEVM-026外形圖(UCD3138PFCEVM-030插在其上)
評估板UCD3138PFCEVM-026主要特性:
• Digitally Controlled PFC Pre-Regulator
• Universal AC Line Input from 90 VAC to 264 VAC with AC Line Frequency 47 Hz to 63 Hz
• Regulated Output 390 VDC with Output from No-Load to Full-Load
• Full-Load Power 360 W, or full-Load Current 0.92 A
• High Power Factor Close to 0.999 and Low THD Below 5% in Most Operation Conditions
• High Efficiency
• Protection:
– Over Voltage
– Over Current
– Brownout
– Power-On Inrush Current
• Test Points to Facilitate Device and Topology Evaluation
• Re-Configurable to Dual-Phase Interleaved PFC or Bridgeless PFC (please contact TI for detail)
評估板UCD3138PFCEVM-026應用:
• Single-Phase Universal AC Line Power Factor Correction Pre-Regulator
• Servers
• Telecommunication Systems
評估板UCD3138PFCEVM-026電性能指標:
圖3.評估板UCD3138PFCEVM-026電路圖(1)
圖4.評估板UCD3138PFCEVM-026電路圖(2)
評估板UCD3138PFCEVM-026材料清單:
圖5.評估板UCD3138PFCEVM-026頂層PCB元件布局圖
詳情請見:
http://www.ti.com/lit/ds/symlink/ucd3138.pdf
和
http://www.ti.com/lit/ug/sluu885a/sluu885a.pdf
The UCD3138 is a digital power supply controller from Texas Instruments offering superior levels of integration and performance in a single chip solution. The flexible nature of the UCD3138 makes it suitable for a wide variety of power conversion applications. In addition, multiple peripherals inside the device have been specifically optimized to enhance the performance of ac/dc and isolated dc/dc applications and reduce the solution component count in the IT and network infrastructure space.
The UCD3138 is a fully programmable solution offering customers complete control of their application, along with ample ability to differentiate their solution. At the same time, TI is committed to simplifying our customer’s development effort through offering best in class development tools, including application firmware, Code Composer Studio. software development environment, and TI’s Fusion Power Development GUI which enables customers to configure and monitor key system parameters.
At the core of the UCD3138 controller are the digital control loop peripherals, also known as Fusion Digital Power Peripherals (FDPP). Each FDPP implements a high speed digital control loop consisting of a dedicated Error Analog to Digital Converter (EADC), a PID based 2 pole–2 zero digital compensator and DPWM outputs with 250 ps pulse width resolution. The device also contains a 12-bit, 265ksps general purpose ADC with up to 14 channels, timers, interrupt control, JTAG debug and PMBus and UART communications ports. The device is based on a 32-bit ARM7TDMI-S RISC microcontroller that performs
real-time monitoring, configures peripherals and manages communications. The ARM microcontroller executes its program out of programmable flash memory as well as on-chip RAM and ROM.
In addition to the FDPP, specific power management peripherals have been added to enable high efficiency across the entire operating range, high integration for increased power density, reliability, and lowest overall system cost and high flexibility with support for the widest number of control schemes and topologies. Such peripherals include: light load burst mode, synchronous rectification, LLC and phase shifted full bridge mode switching, input voltage feed forward, copper trace current sense, ideal diode emulation, constant current constant power control, synchronous rectification soft on and off, peak current mode control, flux balancing, secondary side input voltage sensing, high resolution current sharing, hardware configurable soft start with pre bias, as well as several other features. Topology support has been optimized for voltage mode and peak current mode controlled phase shifted full bridge, single and dual phase PFC, bridgeless PFC, hard switched full bridge and half bridge, and LLC half bridge and full bridge.
UCD3138主要特性:
Digital Control of up to 3 Independent Feedback Loops
Dedicated PID based hardware
2-pole/2-zero configurable
Non-Linear Control
Up to 16MHz Error Analog to Digital Converter (EADC)
Configurable Resolution as Small as 1mV/LSB
Automatic Resolution Selection
Up to 8x Oversampling
Hardware Based Averaging (up to 8x)
14 bit Effective DAC
Up to 8 High Resolution Digital Pulse Width Modulated (DPWM) Outputs
250ps Pulse Width Resolution
4ns Frequency Resolution
4ns Phase Resolution
Adjustable Phase Shift Between Outputs
Adjustable Dead-band Between Pairs
Up to 2MHz Switching Frequency
Configurable PWM Edge Movement
Trailing Modulation
Leading Modulation
Dual Edge Modulation
Configurable Feedback Control
Voltage Mode
Average Current Mode
Peak Current Mode Control
Constant Current
Constant Power
Configurable Modulation Methods
Frequency Modulation
Phase Shift Modulation
Pulse Width Modulation
Fast, Automatic and Smooth Mode Switching
Frequency Modulation and PWM
Phase Shift Modulation and PWM
High Efficiency and Light Load Management
Burst Mode
Ideal Diode Emulation
Synchronous Rectifier Soft On/Off
Low IC Standby Power
Soft Start / Stop with and without Pre-bias
Fast Input Voltage Feed Forward Hardware
Primary Side Voltage Sensing
Copper Trace Current Sensing
Flux and Phase Current Balancing for Non-Peak Current
Mode Control Applications
Current Share Bus Support
Analog Average
Master/Slave
Feature Rich Fault Protection Options
7 High Speed Analog Comparators
Cycle-by-Cycle Current Limiting
Programmable Fault Counting
External Fault Inputs
4–10 Digital Comparators
Programmable blanking time
Synchronization of DPWM waveforms between multiple UCD313x devices
14 channel, 12 bit, 265 ksps General Purpose ADC with integrated
Programmable averaging filters
Dual sample and hold
Internal Temperature Sensor
Fully Programmable High-Performance 31.25MHz, 32-bit ARM7TDMI-S Processor
32 kByte (kB) Program Flash
2 kB Data Flash with ECC
4 kB Data RAM
4 kB Boot ROM Enables Firmware Boot-Load in the Field via
I2C or UART
Communication Peripherals
I2C/PMBus
2 UARTs
JTAG Debug Port
Timer capture with selectable input pins
Up to 5 Additional General Purpose Timers
Built In Watchdog: BOD and POR
64-pin QFN and 40-pin QFN packages
Operating Temperature: –40°C to 125°C
Fusion Digital Power GUI Support
UCD3138應用:
Power Supplies and Telecom Rectifiers
Power Factor Correction
Isolated dc-dc Modules
圖1.UCD3138方框圖
評估板UCD3138PFCEVM-026
This EVM is to help evaluate the UCD3138 64-pin digital control device in off-line power converter application and then to aid its design. The EVM is a standalone Power Factor Correction (PFC) preregulator of single-phase AC input. The EVM UCD3138PFCEVM-026 is used together with its control card, UCD3138CC64EVM-030, also an EVM on which is placed UCD3138RGC.
The EVM of UCD3138PFCEVM-026 together with UCD3138CC64EVM-030 can be used as they are delivered without additional work, from either hardware or firmware, to evaluate PFC. The UCD3138PFCEVM-026 together with the UCD3138CC64EVM-030 can also be re-tuned on its design parameters through the operation of GUI, called Texas Instruments Fusion Digital Power Designer, or reloaded up with custom firmware with user’s definition and development.
The EVM system is in topology of single-phase boost converter at its delivery on both hardware and firmware, but can be re-configured into two other PFC topologies: dual-phase interleaved, and bridgeless, then corresponding operation can be made by reloading with that associated firmware. All necessity of hardware and firmware for the two additional topologies are already developed and delivered with the shipment. Please contact Texas Instruments to obtain the instructions how to make re-configuration.
In the package delivered, three EVMs are included UCD3138PFCEVM-026, UCD3138CC64EVM-030, and USB-TO-GPIO. In the same package, also included is a hard copy of Evaluation Module Electrical Safety Guideline.
This user’s guide provides basic evaluation instruction from a viewpoint of system operation in standalone PFC in its boost configuration.
UCD3138PFCEVM-026 together with UCD3138CC64EVM-030 is an EVM of PFC pre-regulator with digital control using UCD3138 device in boost converter topology and in the application of single-phase AC input.
UCD3138 device is located on the board of UCD3138CC64EVM-030. UCD3138CC64EVM-030 is a daughter card and serves all PFC required control functions with preloaded single-phase boost PFC firmware. UCD3138PFCEVM-026 accepts universal AC line input from 90 VAC to 264 VAC, and outputs nominal 390 VDC with full load output power 360 W, or full output current 0.92 A.
圖2.評估板UCD3138PFCEVM-026外形圖(UCD3138PFCEVM-030插在其上)
評估板UCD3138PFCEVM-026主要特性:
• Digitally Controlled PFC Pre-Regulator
• Universal AC Line Input from 90 VAC to 264 VAC with AC Line Frequency 47 Hz to 63 Hz
• Regulated Output 390 VDC with Output from No-Load to Full-Load
• Full-Load Power 360 W, or full-Load Current 0.92 A
• High Power Factor Close to 0.999 and Low THD Below 5% in Most Operation Conditions
• High Efficiency
• Protection:
– Over Voltage
– Over Current
– Brownout
– Power-On Inrush Current
• Test Points to Facilitate Device and Topology Evaluation
• Re-Configurable to Dual-Phase Interleaved PFC or Bridgeless PFC (please contact TI for detail)
評估板UCD3138PFCEVM-026應用:
• Single-Phase Universal AC Line Power Factor Correction Pre-Regulator
• Servers
• Telecommunication Systems
評估板UCD3138PFCEVM-026電性能指標:
圖3.評估板UCD3138PFCEVM-026電路圖(1)
圖4.評估板UCD3138PFCEVM-026電路圖(2)
評估板UCD3138PFCEVM-026材料清單:
圖5.評估板UCD3138PFCEVM-026頂層PCB元件布局圖
詳情請見:
http://www.ti.com/lit/ds/symlink/ucd3138.pdf
和
http://www.ti.com/lit/ug/sluu885a/sluu885a.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。